1098/1198 standard exhaust system

Discussion in 'Wanted' started by Cranker V2, Nov 18, 2013.

Page 2 of 3
  1. Hows your exhaust Nels? :cool:
     
    #21 bootsam, Nov 19, 2013
  2. Neighbours aint keen..:biggrin:

    70mm boom boom boom...:eek:
     
    #22 Nelson, Nov 19, 2013
    • Like Like x 2
  3. 70mm is my next target. Ive only got the slash cut termi's on the 1198. Still loud mind. Especially since i junked that exhaust valve. 916 has full 54mm. I like starting them both up in my garage. Bass!

    Ive got forgiving neighbours, plus one is a biker too. Result.
     
    #23 bootsam, Nov 19, 2013

  4. My neighbors are mostly ok, when I did the loom / ecu conversion I had to keep running the bike up to temp to check a fault that only exhibited itself when fully warm. He did pop over then! My own fault really, I just stuck the dbs in and all was harmonious again.

    If you're after a full system, don't dismiss the full 848 system for your 10' it's only a few mm smaller and goes on and works a treat.
    Usually a lot cheap.
    It's what I'm running... :upyeah:

    PS. Post up a pic of the exhaust with the flapper gone.
    Did you ditch the tea tray as well?
     
    #24 Nelson, Nov 19, 2013
    Last edited: Nov 19, 2013
  5. Hmmmmmmmmm - Titaniyummy.... Ducati 848 / 1098 SBK Full Exhaust system by Leo Vince | eBay
     
    #25 Nelson, Nov 20, 2013
  6. Storm said a 996/1198 conversion system would be:


    The system made in 54mm would be £950 in titanium and £650 in stainless steel.
     
    #26 Cranker V2, Nov 20, 2013
  7. Wow! Gone down a lot since last year! :upyeah:
     
    #27 Nelson, Nov 20, 2013
  8. Wonder if it'd be cheaper to get them to make me a set of 70mm S/S for my termis than buy the things from termi. Coz thats not a bad price shown above.
     
    #28 bootsam, Nov 20, 2013
  9. Remember you're a Womble... No, that's not it, remember the quoted "70mm" is only a small part of the zorst, most of it is ~ 50mm + a bit.
     
    #29 Nelson, Nov 20, 2013
  10. Is it indeed? Thanks.

    My clutch nut arrived. :)
     
    #30 bootsam, Nov 20, 2013
  11. Don't forget to check the number of teeth while you're in there :wink:
     
    #31 Nelson, Nov 20, 2013
  12. 48 shall be the number of the count; and the number of the count shall be 48...

    Had to pay customs £12 sobs for it. Fleecing bastards.
     
    #32 bootsam, Nov 20, 2013
  13. bootsam, I am looking for a 70mm header for my 1198s as well, what do you think is a good price? I've tracked one down but they only want to sell with the ecu and its about £750.00
     
    #33 Maccaa, Nov 21, 2013
  14. The map for the headers is different to the slip on map so might be worth getting
     
    #34 abmatt2002, Nov 21, 2013
  15. Hi Matt, was going to get either my original ecu or the slip on ecu re mapped by CJS when I get the new header if I dyno it or a re flash of one by chrisw possibly.

    Cranker V2 sorry for taking this off topic, will start new thread.

    Sorry Maccaa
     
    #35 Maccaa, Nov 21, 2013
  16. Personally I'd keep the other 2 and get the 3rd custom mapped by cjs
     
    #36 abmatt2002, Nov 21, 2013
  17. £750 seems fair enough. Agree about CJS too, although ChrisW can flash the ecu to remove the lamba sensors and exhaust valve shite that might give you an error on the dash in the meantime before CJS tart it up.
     
    #37 bootsam, Nov 21, 2013
  18. #38 deleteduser211220, Nov 21, 2013
  19. You are missing a 1 at the start of the price.
     
    #39 deleteduser211220, Feb 16, 2014
  20. really……..1950 and 1650…..:biggrin:
     
    #40 andyb, Feb 16, 2014
(You must log in or sign up to post here.)
Page 2 of 3
Do Not Sell My Personal Information